U-Boot 1.1.6 (Dec 16 2011 - 07:05:02)

CPU:   8548, Version: 2.1, (0x80310021)
Core:  E500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU:1200 MHz, CCB: 400 MHz,
       DDR: 200 MHz, LBC:  25 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: CDS Version 0x01, PCI Slot 1
CPU Board Revision 0.0 (0x0000)
    PCI1: 32 bit, unknown MHz, async
    PCI2: disabled
Parkes Version : 0x00340001
Parkes reset history = 0x00000010
Parkes default uart mux = 0x0000bc78
Parkes default watchdog = 0x00000388
reset = 0x0
Enable the Switch reset & Hreset = 0x7
Enable the watchdog = 0x00000389
Load the watchdog timer value = 0x9828
Correct : POR - PLL ratio status register = 0x00c6400c
Correct : POR - Boot mode status register = 0x85370000
Correct : POR - I/O impedance status and control register = 0x0003007f
Correct : POR - I/O device status regsiter = 0x829fea67
Correct : POR - Debug mode status register = 0x0f000000
Correct : Device disable control register = 0x51000000
DRAM:  Initializing
Manufacturer part number of DDR SG572288JNP535U1SF
DDRCDR  - DDR CONTROL DRIVER REGISTER = 0x00080000
PARKES:  1 MB
  TAKE ALL DEVICES OUT OF RESET
    DDR: 1024 MB
Running Memory Test from ROM !
.....
Now running in RAM - U-Boot at: 3ff60000
POST: U-boot memory location PASSED
Flash Manufacturer Id 0x17e
FLASH:16 MB
L2 cache 512KB: enabled
*** Warning - bad CRC, using default environment

Scaning PCI bus:
Found BCM Network Controller, (0, 18, 0), (14e4, b214)
Found OHCI Network Controller, (0, 19, 0), (1131, 1561)
Found EHCI Network Controller, (0, 19, 2), (1131, 1562)

Scaning PCIE bus:
Found MPC8548E PCIE Controller, (0, 0, 0), (1957, 13)
Link Training Status State Machine reg  = 0x16
The Link Satus reg =  0x41
Correct link width trained :x4
    BAR0 = 0xfef00000
Found PLX PEX8508 PCIE Switch, (1, 0, 0), (10b5, 8508)
    BAR0 = 0xe8000000
Found PLX PEX8508 PCIE Switch, (2, 1, 0), (10b5, 8508)
Found PLX PEX8508 PCIE Switch, (2, 2, 0), (10b5, 8508)
Found PLX PEX8508 PCIE Switch, (2, 3, 0), (10b5, 8508)
Found PLX PEX8508 PCIE Switch, (2, 4, 0), (10b5, 8508)
Found Silicon Image Sil3132 SATA, (12, 0, 0), (1095, 3132)
    BAR0 = 0xe8100000    BAR1 = 0x0
    BAR2 = 0xe8104000    BAR3 = 0x0
PCIE scan complete, last bus = 12

In:    serial
Out:   serial
Err:   serial
SATA:  channel HW reset time=0ms
SATA connect status=00000000
phy reset found no device on port 0
Can not start port 0
channel HW reset time=0ms
SATA connect time=10ms
sata phy reset found device on port 1
reset timeout - no device found
Can not start port 1
scanning bus for devices...
port 0 not started
SCSI command 0x12 ret errno -5
SCSI command 0x00 ret errno -1
Net:   Set PHY BCM5461 to SGMII mode done!
eTSEC1, eTSEC2, eTSEC3
Running POST TEST

USB:   Base Address = 0x80010000
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
POR = 0x51000000 and reset history = 0x00000010
value for reg 0x1c in phy 1 = 0x54890010
ELF file is 32 bit
Loading .text @ 0x00010080 (176836 bytes)
Loading .rodata @ 0x0003b344 (13576 bytes)
Loading .rodata.str1.4 @ 0x0003e84c (15423 bytes)
Loading set_Xcommand_set @ 0x0004248c (88 bytes)
Loading .data @ 0x00043000 (14876 bytes)
Loading .sdata @ 0x00046a1c (80 bytes)
Clearing .sbss @ 0x00046a70 (260 bytes)
Clearing .bss @ 0x00046b78 (9360 bytes)
## Starting application at 0x00010080 ...
Consoles: U-Boot console
Found compatible API, ver. 65542
Will try to boot from
USB
Compact Flash
Hard Disk

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.2
(xhong@ipg-pool1-11.juniper.net, Thu Aug 21 08:51:56 PDT 2008)
Memory: 1024MB

can't load '/kernel'
can't load '/kernel.old'

Type '?' for a list of commands, 'help' for more detailed help.
loader> show
LINES=24
baudrate=9600
boot.ver=1.6
bootcmd=cp.l 0xffe00000 0x100000 0x30000; bootelf 0x100000
bootdelay=3
consoledev=ttyS1
currdev=disk0:
ethact=eTSEC1
ethaddr=00:21:59:9f:**:**
gatewayip=10.150.55.254
hw.resethistory=0x00000010
hw.uart.console=mm:0xfef00200,rs:2
hw.uart.dbgport=mm:0xfef00200,rs:2
interpret=OK
ipaddr=10.150.52.34
loadaddr=200000
loaddev=disk0:
loads_echo=1
netdev=eth0
netmask=255.255.248.0
post.cpu=PASSED
post.ether=PASSED
post.pcie=PASSED
post.ram=PASSED
prompt=loader>
serverip=10.150.52.32
stderr=serial
stdin=serial
stdout=serial
use_bootp=1
loader>